> Error Code
> Canon Fax Error Codes
Canon Fax Error Codes
If the machine still does not communicate with the cascade copy printer, contact your System Manager. #825 Cause 1 The Department ID and password set on the host machine do not Cause: BJ Cartridge (BJ head) malfunction. Provides a description of the possible cause of the error code in question. 6. Page 71 Chapter 2: Service Error Codes ##100 [ TX ] The number allowed for retransmission of the procedure signal was exceeded during transmission Cause Remedy • The transmission level is navigate here
Remedy 2 Check the proxy settings. (See "Protocol Settings.") #869 Cause Received a response from the destination stating that authentication failed when sending with WebDAV (received HTTP Error 401: Unauthorized). Solution: Lower the transmission start speed to 4800 bps. Solution: Have the other party lower their transmission speed to 4800 bps. Cause 2 When transmitting to a destination stored in the Address Book, transmission could not be performed because the specified destination stored in the Address Book was deleted while the documents
Canon Fax Error Codes
Remedy Check the Remote Fax Server. A. A. Remedy 3 Make sure that the SSL server certificate is not a self-signed certificate. #845 Cause When sending with POP before SMTP, POP authentication (POP AUTH) failed.
Solution: Boost the transmission level so that the other party can receive signals properly. Page 20 Chapter1: User Error Codes #010 [ TX/RX ] Communications control memory overflow Cause Remedy • There is no recording paper so that the con- • Set recording paper. Remedy Change the Department ID and password, and try again. Canon Result Ng Solution: Adjust the NL equalizer so the other party can receive picture signals properly.
Remedy Confirm that the recipient's machine is able to communicate, and then try again. Canon Fax Error Code Ng Cause: The ink sensor is defective. nel not available) arrived from the network. • Print out a communications analysis list, and analyze it. Solution: Boost the transmission level so that the other party can receive carrier signals properly.
SSL communication is performed via a proxy. Canon Fax Machine Error Codes A. Cause 3 is set to 'Off'. Increase the T1 timer setting: Increase the setting of No.l 1.
Canon Fax Error Code Ng
Cause: Other party cannot properly receive the G12 signals due to poor line conditions. Reset the Cleaning absorption pad capacity to 0, in the service mode. Canon Fax Error Codes Cause: The read end sensor stays ON or OFF. Canon Error #099 Check the destination settings. #755 Cause 1 The fax could not be sent from the Remote Fax client machine because TCP/IP is not operating normally.
Page 142 Chapter 2: Service Error Codes ##552 [ TX ] DTMF IC malfunctioned Cause Remedy • The DTMF IC is faulty (failing to become • Replace the unit that includes http://attavik.net/error-code/canon-copier-error-codes.html Remedy 1 Set Use Chunked Encoding with WebDAV Sending to 'Off'. (See "Dividing Data Into Chunks When Sending with WebDAV.") Remedy 2 Check the settings for the WebDAV server. #876 Cause available) arrived from the network. • Print out a communications analysis list, and analyze it. Cause 2 An incorrect destination was specified for the sending of an e-mail message or I-fax. Canon Error Code 801 Scan Folder
Cause: The other machine is out of paper. Solution: Have the other party lower the transmission start speed to 4800 bps. Solution: Replace the button control unit (operation unit, etc.). ##232 [ TX ] ENCODE control unit malfunction. his comment is here Page 87 • In the case of DTC reception, the proce- • Record the protocol on a DAT or MD, and dure signal is faulty.
Loosen the RTN signal transmission condition: Increase the settings of No.02, 03, and 04. Canon Imagerunner Error Codes 099 Page 214 Chapter 2: Service Error Codes ##1059 [ TX/RX ] Called party is busy (All B-channel are occupied) [German model] Cause Remedy • Cause number #59 (Called party is busy Remedy Set the Different Size Originals mode, and then try scanning again.
Cause: The caller disconnected the line or unable to detect the signal from the caller.
Remedy Check the settings for the POP Server in Communication Settings. (See "Common Communication Settings for E-Mail/I-Fax.") Confirm that the POP server is functioning normally. Cause: Power unit trouble Solution: Replace power unit ##330 [ TX / RX ] Power supply unit ACVIN signal abnormality. B. (If the CS does not stop at the right edge of the document): 1. G3 Fax B. (If the CS does not stop at the CS reference position): 1.
Page 56 Chapter1: User Error Codes #997 [ TX/RX ] Power was cut during a communication Cause Remedy • The power went out or was turned off dur- • Correct it Cause: BJ cartridge (BJ head) malfunction. Page 180 Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. http://attavik.net/error-code/canon-imagerunner-error-codes.html Cause: Line noise.
Page 84 Chapter 2: Service Error Codes ##200 [ RX ] During image reception, a carrier is not detected for 5 sec Cause Remedy • The line condition is poor, and Cause: SCNT PWB trouble. ST. Solution: Boost the transmission level so that the other party can receive NACK properly.
A. Solution: Have the other party boost the transmission level to receive EOM or PIS properly. ##506 [ RX ] Fail phase synchronization during G1 reception. Remedy Turn the main power OFF, wait for 10 or more seconds, and turn the main power back ON. Solution: Boost the transmission level so the other party can receive picture signals properly.
Remedy Ask the recipient to load paper into their fax machine. #018 Cause 1 The recipient's machine did not respond when your machine redialed. Let the machine sit for awhile so BJ head can cool down and retry. Cause: Cannot receive signals properly due to poor line conditions. Cause: (After TCF transmission before picture signals); The other party experience echo malfunction.
Page 166 Chapter 2: Service Error Codes ##740 [ RX ] In CHT reception, the other party could not use fall-back Cause Remedy • The line condition is poor, and TCF Remedy Wait until the Address Book Import/Export function from the Remote UI or the other sending component is complete, and then try sending again. #711 Cause 1 The Mail Box and Solution: Replace the modem or modem attached circuit board. Remedy Ask the sender to reduce the amount of text data in the body of the document, and then resend the data. #837 Cause A connection request was received from a
Cause: The other party cannot receive properly due to poor line conditions.