> Error Code
> Case Ih Puma Fault Codes
Case Ih Puma Fault Codes
ENG 211 Communications problem with Armrest, Instrumentation, or Transmission Controllers ENG 212 Oil Temperature Sensor Voltage is too high ENG 213 Oil Temperature Sensor Voltage is too low ENG 214 Oil Error codes should clear and transmission shift. If the tractor has high hours, before replacement of the EPL, remove and inspect the park brake assembly pads for wear. TMF 31 Left Draft Pin voltage is outside the normal operating range. http://attavik.net/error-code/carrier-furnace-fault-codes.html
Occ integrity check should return an exit code different... Trans 2811 Transmission Oil Temperature Hot Trans 2812 Transmission Oil Temperature sensor short to B+ or open circuit Trans 2813 Transmission oil temperature Sensor Short to Ground Trans 2814 Integrated Control INST 12071 Communications Lost with Transmission Controller INST 12091 Communications Lost with Engine Controller INST 12101 Communications Lost with Tractor ECU (Gateway) Controller INST 12111 Communications Lost with Automatic Temperature Controller Engine 3128 Hand Throttle -Channel Difference Error Engine 3129 Hand Throttle -Idle Switch Closed Circuit Engine 3130 Hand Throttle -Idle Switch Open Circuit Engine 3131 Grid Heater Always Switched On Engine
Case Ih Puma Fault Codes
Register Now In order to be able to post messages on the The Combine Forum forums, you must first register. It only Seams to do it when the tractors cold and it's a bit slower at starting up seaming like a voltage drop on start up causes it ? Bman So if a machine has a problem with a component Case IH 8230 combine fault code E1563-03, fuel temp signal.
TRANS 75 Engine speed from Inst Controller does not match the speed signal from the alternator. Original!! INST 1015 Seat Switch may be stuck closed. Case Ih Transmission Fault Codes ENG 418 Water in Fuel sensor indicates the water in the fuel filter needs to be drained.
I wonder if somebody manually released it or somebody doesn't have it set right. Case Puma Error Code 12188 Pulling the shoot trailer on beaters day! ENG 396 Rear Fueling current is too low ENG 397 Rear Fueling current is too high ENG 398 Rear Timing current is too low ENG 399 Rear Timing current is too ENG 298 OEM Pressure Sensor Voltage is too low.
ENG 583 Fuel Inlet Pressure Sensor voltageout of range high or low. Case Ih Code Reader NOTE: The Bowden cable connects the EPL to the handbrake actuator. ENG 451 Fuel Pressure Sensor voltage is too high ENG 452 Fuel Pressure Sensor voltage is too low ENG 456 Fuel Pressure in pump is not changing with operating conditions. D Wesselingh is offline Quote Quick Reply Remove Advertisements Sponsored Links The Combine Forum Advertisement Reply Page 1 of 2 1 2 vBulletin Message Cancel Changes Quick Reply
Case Puma Error Code 12188
Code 12132, 12133, 12142 - these codes indicate that the can bus is open between the EPL and other controllers. NOTE: Error code 12202 'Hand Brake Incongruence' can also be caused by the incorrect operation of the other hand brake switch contacts. Case Ih Puma Fault Codes NH 4187 EHR Joystick potentiometer Y short circuit. Case Ih Error Codes ENG 2186 Supply Voltage to the accelerator pedal position sensor too low.
If the code returns, replace the EPL. have a peek at these guys If ok test circuit to B3. ENG 489 Measured Speed Sensor data low ENG 491 Wastegate 2 voltage is too high ENG 492 Wastegate 2 voltage is too low ENG 493 The Injection Control Identifier Circuit in Check the RT controller for error codes and correct before attempting to repair the EPL. Case Puma 165 Problems
Does anyone know what this fault is? Refbacks are On. Pulling the shoot trailer on beaters day! check over here The tractor acts like the electronic parking brake won't release when you put it in gear.
ENG 2322 Engine Camshaft Speed / Position Sensor data invalid. Case Ih Tractor Error Codes ENG 582 Fuel inlet Pressure Sensor voltage is too low. To adjust the cable, loosen the locking nut (E) and adjust the bolt (F) until the correct measurement is obtained.
NH 3118 Power supply for sensors - NOT PLAUSIBLE NH 3119 Power supply for sensors - NO SIGNAL NH 3120 Power supply for sensors - ALL OTHER FAULTS NH 3121 PTO
ENG 299 Engine Shutdown by other than keyswitch (i.e. ENG 352 5 Volt Sensor Supply voltage is too low ENG 378 Front Fueling current is too low ENG 379 Front fueling current is too high ENG 381 Error detected in It only Seams to do it when the tractors cold and it's a bit slower at starting up seaming like a voltage drop on ... New Holland Error Codes TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration.
Anyone know what this refers to, as I cannot find a list of codes in the manual. TMF 23 Two draft pin sensors failed when configured for two draft pins. TMF 125 Aux 1st Raise Coil solenoid shorted to 12 volts. this content TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration.
The service manual does contain the code number descriptions. Code 12024 , 12052 and 12053 - perform tests 1, 2 and 3 below. Ensure the EPL channel 2 is set to 'NO' and the instrument cluster IE channel 2 set to 'NO'. If the voltage is incorrect test the circuit.
All times are GMT -4. ← Previous Post Next Post → If you enjoyed this article please consider sharing it! Notice: How to check your history 21.01.2015? ENG 187 Sensor Supply 2 Voltage is too low. Notice: The list members receive Payment Monthly 12-2015 Notice: How to get Payment Monthly on forum [30.03.2015] New Post Earn Money Download Files How to post ?
INST 1034 Hydraulic oil filter switch shorted to ground on power up. ENG 2266 Electric Lift Pump for Engine Fuel Supply Voltage too low. Add coolant fluid. Hitch 1015 Five-volt reference is below the lower voltage limit.
If Ok the RE/RT controller may be faulty. Trans 2055 No signal from wheel speed sensor. truck S-Mod Joined: May 9, 2014 Messages: 2,231 Likes Received: 184 If you download this document, you will be lost Gallons CASE IH & NEW HOLLAND FAULT CODES TYPE CODE ERROR TMF 41 Draft pin(s) detected but the Armrest controller specified tractor without draft control.
Trans 2009 Seat switch open circuit Trans 2010 Seat switch is shorted to the supply voltage B+ or 5 volt reference Trans 2011 Clutch Pot Open Circuit or short to ground Can Bus codes include: 12132, 12133, 12142, 12143, 12144, 12145, 12146, 12147, 12148, and 12150.